环境温度对A6N01铝合金焊接接头力学性能及微观组织的影响
Effect of Temperature on Mechanical Properties and Microstructure of Welded Joints of A6N01 Aluminum Alloys
DOI: 10.12677/MET.2017.62014, PDF, HTML, XML, 下载: 1,642  浏览: 2,438 
作者: 戴忠晨*, 金文涛, 云中煌, 吴金津, 孙景南：南车南京浦镇车辆有限公司，江苏 南京；苟国庆, 覃 超：西南交通大学材料科学与工程学院，四川 成都
关键词: A6N01铝合金；环境温度；力学性能；微观组织；A6N01 Aluminum Alloys； Temperature； Mechanical Properties； Microstructure
摘要: 在−20℃、−10℃、0℃、20℃的温度条件下对A6N01铝合金焊接接头进行焊接，测试不同环境温度条件下焊接接头的拉伸强度，冲击韧性，硬度以及显微组织。研究结果表明，温度对A6N01铝合金对接接头的抗拉强度的数值影响不大，但是接头断裂的位置发生了变化，这可能需要引起重视。温度对A6N01铝合金对接接头的冲击韧性的数值影响较大。在常温情况下的焊缝中可以观察到较多的析出相，而随着温度下降，析出相逐渐减少，气孔和夹渣也较少。
Abstract: The welded joints of A6N01 are fabricated at the temperature of -20˚C, -10˚C, 0˚C and 20˚C and the tensile strength, impact toughness, microhardness and microstructure were studied. The results showed that the temperature didn’t change the tensile strength but affected the fracture location. The temperature affects the impact toughness in large amount. A lot of precipitate phases precipitated from the weld zone in the normal temperature but the much less precipitate phases with the decrease of the temperature, and the porosity and slag decreased too.
文章引用：戴忠晨, 金文涛, 云中煌, 吴金津, 孙景南, 苟国庆, 覃超. 环境温度对A6N01铝合金焊接接头力学性能及微观组织的影响[J]. 机械工程与技术, 2017, 6(2): 98-103. https://doi.org/10.12677/MET.2017.62014

参考文献

[1] Gou, G., Zhang, M., Chen, H., Chen, J., Li, P. and Yang, Y.P. (2015) Effect of Humidity on Porosity, Microstructure, and Fatigue Property of A7N01S-T5 Aluminum Alloy Welded Joints in High Speed Trains. Materials and Design, 85, 309-317.
[2] Zhu, X.K. and Chao, Y.J. (2002) Effects of Temperature-Dependent Material Properties on Welding Simulation. Computers and Structures, 80, 967-976.
[3] Jang, K.C. and Lee, D.G. (2005) Welding and Environmental Test Condition Effect in Weld Ability and Strength of Al Alloy. Journal of Materials Processing Technology, 164-165, 1038-1045.
[4] Ashton, R.F., Wesley, R.P. and Dixon, C.R. (2003) The Effect of Porosity on 5086-H116 Aluminum Alloy Welds. Welding Research, 25, 315-320.
[5] Linder, J., Axelsson, M. and Nilsson, H. (2006) The Influence of Porosity on the Fatigue Life for Sand and Permanent Mould Cast Aluminum. International Journal of Fatigue, 28, 1752-1758.

为你推荐