数控技术课程中超硬材料切削加工所涉及的关键问题的引入Introduction of Key Problems in Super Hard Material Cutting in NC Technology Course
董新峰, 仇中柱, 韩清鹏 下载量: 777 浏览量: 2,934
教育进展 Vol.9 No.3, May 29 2019, PDF, HTML, XML DOI:10.12677/AE.2019.93063 被引量
悬索桥索鞍索槽曲面数控加工技术研究与探讨Research and Discussion on NC Machining Technology of Saddle Cable Groove Surface of Suspension Bridge Cable
董小亮, 唐长平, 刘令娴 下载量: 337 浏览量: 737
机械工程与技术 Vol.10 No.5, October 28 2021, PDF, HTML, XML DOI:10.12677/MET.2021.105062 被引量
基于模糊控制理论的数控加工参数的自适应控制研究Adaptive Control of CNC Machining Parameters Based on Fuzzy Control Theory
刘恒丽 下载量: 641 浏览量: 1,235
动力系统与控制 Vol.10 No.2, March 31 2021, PDF, HTML, XML DOI:10.12677/DSC.2021.102011 被引量
“互联网+”视域下高职智慧课堂教学模式的研究与应用——以《数控加工与编程》课程为例Research and Application of the Intelligent Classroom Teaching Mode in Higher Vocational Education under the Perspective of Internet Plus—Taking the Course of Numerical Control Machining and Programming as an Example
兰叶深, 徐文俊, 徐建亮, 刘文军 下载量: 524 浏览量: 1,172 科研立项经费支持
职业教育 Vol.9 No.2, April 15 2020, PDF, HTML, XML DOI:10.12677/VE.2020.92019 被引量
叶轮加工中心X轴滑座动态特性分析与优化Dynamic Characteristic Analysis and Optimization of the X Axis Slide of Impeller Machining Center
陈达 下载量: 1,897 浏览量: 2,991 国家科技经费支持
机械工程与技术 Vol.5 No.3, September 26 2016, PDF, , XML DOI:10.12677/MET.2016.53025 被引量
三次三角插值样条曲线的数控插补计算方法An NC Interpolation Calculation Method of Cubic Trigonometric Cardinal Interpolation Spline
张益汉, 宋爱平, 刘祖奇, 邱 林 下载量: 2,558 浏览量: 7,446
机械工程与技术 Vol.4 No.2, June 25 2015, PDF, , XML DOI:10.12677/MET.2015.42016 被引量
数控加工中3D表面形貌数字图像处理技术3D Surface Topography Analysis Using Image Processing Technology in NC
陈慧群 下载量: 3,201 浏览量: 9,849 科研立项经费支持
机械工程与技术 Vol.2 No.4, December 30 2013, PDF, , DOI:10.12677/MET.2013.24028 被引量
数字赋能高职《数控加工与编程》课程思政教学的建设与研究Construction and Research on Curriculum Ideology and Politics of Digital Empowerment of Higher Vocational “CNC Machining and Programming” Course
兰叶深, 饶楚楚, 叶云霞, 徐文俊 下载量: 124 浏览量: 276 科研立项经费支持
教育进展 Vol.13 No.7, July 18 2023, PDF, HTML, XML DOI:10.12677/AE.2023.137692 被引量
数控铣削加工参数离线–在线优化研究及应用Research and Application of Off-Online Optimization of CNC Machining Parameter
刘恒丽, 王 勇, 董靖川, 刘日鑫 下载量: 495 浏览量: 936
机械工程与技术 Vol.9 No.1, February 25 2020, PDF, , DOI:10.12677/MET.2020.91002 被引量
五轴数控机床进给系统动态误差影响因素分析Analysis of the Factors Affecting the Dynamic Error of the Feed System of Five Axis NC Machine Tools
郭玉玺, 陈光胜 下载量: 235 浏览量: 419
建模与仿真 Vol.12 No.1, January 19 2023, PDF, HTML, XML DOI:10.12677/MOS.2023.121019 被引量