镁合金车轮动态特性分析及弯曲疲劳寿命预测
Dynamic Characteristic Analysis and Prediction of Bending Fatigue Life of Magnesium Alloy Wheels
摘要:
本文尝试应用有限元分析软件ANSYS workbench，对镁合金车轮进行弯曲疲劳仿真分析，找到该车轮上应力最大的点即危险点和该点上相对应的应力值，利用所得应力值与名义应力法对车轮的寿命进行预测，并将得到的结果与通过软件分析所得结果进行比较；对车轮的其他动态特性进行分析，再将分析结果与铝制车轮进行对比，研究结果提出了车轮合理设计的发展方向。
Abstract:
In this paper, bending fatigue simulation analysis was carried out on the magnesium alloy wheels using the software ANSYS workbench of finite element analysis. For the wheels studied, the stress of dangerous points and the corresponding stress values were obtained. Moreover, the fatigue life of the wheel has been predicted based on the nominal stress method, and the results predicted were compared with the results through the analysis of the software. Other dynamic characteristics of wheels were also analyzed, and then compared with the analysis results of aluminum wheels. The results indicate a design development direction for wheels.
参考文献
|
[1]
|
崔胜民, 杨占春. 汽车车轮疲劳寿命预测方法的研究[J]. 机械强度, 2002(4): 617-619, 631.
|
|
[2]
|
Stearns, J. and Srivat-san, T.S. (2004) Modeling the Mechanical Response of an Aluminum Alloy Automotive Rim. Materials Science and Engineering: A, 366, 262-268.
http://dx.doi.org/10.1016/j.msea.2003.08.017
|
|
[3]
|
王在伟, 焦青. SolidWorks与ANSYS之间的数据交换方法研究[J]. 煤矿机械, 2011, 32(9): 248-250.
|
|
[4]
|
王霄锋, 梁昭, 张小格. 基于动态弯曲疲劳试验的汽车车轮有限元分析[J]. 拖拉机与农用运输车, 2007, 34(1): 44-47.
|
|
[5]
|
王勖成. 有限单元法[M]. 北京: 清华大学出版社, 2003.
|
|
[6]
|
秦淑颖, 刘勇兵, 崔红, 等. 富Ce稀土对AZ91D镁合金高周疲劳性能的影响[J]. 特种铸造及有色合金, 2007, 27(10): 750-752.
|
|
[7]
|
赵少汴, 王忠保. 抗疲劳设计——方法与数据[M]. 北京: 机械工业出版社, 1997.
|
|
[8]
|
李舜酩. 机械疲劳与可靠性设计[M]. 北京: 科学出版社, 2006.
|
|
[9]
|
王德俊, 何雪浤. 现代机械强度理论及应用[M]. 北京: 科学出版社, 2003.
|
|
[10]
|
孙红梅. 轿车铝合金车轮模态计算和优化设计[D]: [硕士学位论文]. 秦皇岛: 燕山大学, 2007.
|
|
[11]
|
郑松林, 郑钻玺, 徐洪慧, 等. 汽车镁合金车轮动态特性分析[J]. 汽车工程, 2011(2): 148-151.
|