机械工程与技术  >> Vol. 6 No. 2 (June 2017)

塔机螺栓连接有限元建模及动态载荷分析
Finite Element Modeling of Tower Bolt Connection and Dynamic Load Analysis

DOI: 10.12677/MET.2017.62013, PDF, HTML, XML, 下载: 994  浏览: 3,521  国家自然科学基金支持

作者: 张 烨:山东建筑大学机电工程学院,山东 济南;王胜春:山东省高校机械工程创新技术重点实验室,山东 济南

关键词: 螺纹副解析法横向动态载荷摩擦系数承载力Screw Pairs Analytical Method Transverse Dynamic Loads Friction Coefficient Bearing Capacity

摘要: 考虑螺纹升角建立螺栓联接的三维有限元模型,利用ABAQUS进行有限元分析,采用直接加载的方式施加预紧力,模拟螺纹联接副的承载力,并与Yamamoto解析法进行了对比验证。在此基础上施加横向动态载荷,研究了动态载荷作用下螺纹副不同的摩擦系数对应的螺纹承载力的变化情况。
Abstract: Considering the thread Angle to establish the three-dimensional finite element model of bolt connection, using ABAQUS finite element analysis, with the method of direct load exerted preload, simulation of the bearing capacity of the threaded connection vice, and compared with Yamamoto analytic method is used for validation. Applying transverse dynamic loads, on the basis of dynamic loads is studied under the action of thread pair of different friction coefficient of the corresponding changes of the bearing capacity of screw thread.

文章引用: 张烨, 王胜春. 塔机螺栓连接有限元建模及动态载荷分析[J]. 机械工程与技术, 2017, 6(2): 91-97. https://doi.org/10.12677/MET.2017.62013

参考文献

[1] 侯世远, 廖日东. 螺纹联接松动过程的研究现状与发展趋势[J]. 强度与环境, 2014(2): 39-52.
[2] Junker, G.H. (1973) Criteria for Self-Loosening of Fasteners under Vibration. Aircraft Engineering & Aerospace Technology, 45, 314-335.
https://doi.org/10.1108/eb034981
[3] Nassar, S.A. and Housari, B.A. (2006) Effect of Thread Pitch on the Self-Loosening of Threaded Fasteners Due to Cyclic Transverse Loads. ASME Journal of Pressure Vessel Technology, 128, 590-598.
https://doi.org/10.1115/1.2349572
[4] Nassar, S.A. and Housari, B.A. (2007) Study of the Effect of Hole Clearance and Thread Fit on the Self-Loosening of Threaded Fasteners. Journal of Mechanical Design, 129, 1053-1062.
https://doi.org/10.1115/1.2717227
[5] Schneiders, R. (1996) A Grid-Based Algorithm for the Generation of Hexahedral Element Meshes. Engineering with Computers, 12, 168-177.
https://doi.org/10.1007/BF01198732
[6] Tekkaya, A.E. and Kavakli, S. (1995) 3-D Simulation of Metal-Forming Processes with Automatic Mesh Generation. Steel Research, 66, 377-383.
https://doi.org/10.1002/srin.199501141
[7] 山本晃. 螺纹联接的理论与计算[M]. 上海: 上海科学技术文献出版社, 1984.
[8] Sanclemente, J.A. and Hess, D.P. (2007) Parametric Study of Threaded Fastener Loosening Due to Cyclic Transverse Loads. Engineering Failure Analysis, 14, 239-249.