钢制安全壳涂料老化评价及性能分析
The Evaluation and Analysis after Aging Test of Steel Containment Coatings
DOI: 10.12677/MS.2019.99109, PDF,    科研立项经费支持
作者: 刘艳红*, 郑明珉, 王晓婧, 李怀林, 夏海鸿：国家电投集团科学技术研究院，北京；包玉振, 王君栋, 沈 斌：国核示范电站有限责任公司，山东 威海；张影策：北京科技大学材料科学与工程学院，北京
关键词: 钢制安全壳；涂料；自然老化；AP1000；CAP1400；Steel Containment； Coating； AP1000； CAP1400； Corrosion Resistance； Natural Ageing
摘要: 钢制安全壳是AP1000和CAP1400核电站的第三道防线，也是核电站的最外层防护，其作用尤为重要。因此安全壳上涂装的涂料，需要有效的提高抗腐蚀性能，延长服役寿命。对于采用非能动安全系统的核电站安全壳，除了要满足核电专用涂料的耐辐照、耐化学腐蚀、耐盐雾等性能要求外，还必须具备满足规定的传热性、附着力和润湿性等要求。本研究采用自然老化的方式研究涂料在自然老化前后的性能变化，自然老化在核电站附近的暴晒场进行，其环境因素与实际环境相同。本文较系统的研究了安全壳涂料经过自然老化后的微观结构、形貌、厚度、结合力、润湿性、热导率和电化学性能。
Abstract: Steel containment plays an important role in the AP1000 and CAP1400 nuclear reactors. It is not only the third-line defense but also the outermost protection of reactors. The coatings on steel con-tainment should improve the corrosion resistance and prolong the service life of reactors at the same time. The coatings should also meet the Wrequirements of diathermancy, adhesive force and wettability besides the irradiation resistance, chemical resistance and salt spray resistance. The performance changes of coatings before and after natural aging were studied with the method of natural aging. The natural aging was carried out in the exposure field near the nuclear power plant, of which the environmental factors were the same as the actual environment. Microstructure, sur-face appearance, bonding strength, wettability, thermal conductivity and electrochemical perfor-mance after natural ageing were systematically analyzed in our study.
文章引用：刘艳红, 郑明珉, 包玉振, 王君栋, 张影策, 王晓婧, 李怀林, 夏海鸿, 沈斌. 钢制安全壳涂料老化评价及性能分析[J]. 材料科学, 2019, 9(9): 878-889. https://doi.org/10.12677/MS.2019.99109

参考文献

[1] 朱瑞峰, 吴崇志, 苏靖杰, 等. AP1000钢制安全壳选材及应用[J]. 制造与安装, 2016, 33(3): 56-60.
[2] 袁旭光, 王留方. M310和AP1000核电站用涂料性能指标对比[J]. 涂料工业, 2013, 43(10): 64-68.
[3] 叶成, 郑明光, 王勇, 等. AP1000钢制安全壳厚度对传热性能的影响[J]. 原子能科学技术, 2014, 48(3): 457-461.
[4] 王国彪, 晏桂珍, 王洋, 等. AP1000核电站钢制安全壳涂层工艺改进[J]. 电镀与精饰, 2015, 37(12): 18-22.
[5] 王洋, 晏桂珍, 刘茂平, 等. AP1000核电站钢制安全壳无机富锌涂层施工工艺研究[J]. 涂料工业, 2017, 47(10): 71-74.
[6] 林金平, 黄娜. AP1000核电站钢制安全壳涂装质量控制[J]. 电镀与精饰, 2013, 35(11): 20-23.
[7] 王洋, 晏桂珍, 刘茂平. AP1000核电站钢制安全壳无机富锌涂层直线对接工艺研究[J]. 涂层与防护, 2018, 39(4): 4-7.
[8] Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers. D4541-09.
[9] 刘会成, 程煜, 吴权, 等. 核级无机富锌保护涂层表面润湿性能的研究[J]. 中国涂料, 2014, 29(9): 49-52.
[10] 张耀, 张忠伟, 黄祖兵. 核电站适用涂层特点分析[J]. 上海涂料, 2007, 45(4): 41-42.
[11] 谢德明. 富锌涂层的电化学研究[D]: [博士学位论文]. 杭州: 浙江大学, 2002.
[12] 倪维良, 刘晓强, 郭亮亮, 等. 核电站安全壳涂层腐蚀试验机性能评价[J]. 涂料技术与文摘, 2017, 38(12): 1-5.
[13] Liu, X., Xiong, J., Lv, Y., et al. (2009) Study on Corrosion Electrochemical Behavior of Several Different Coating Systems by EIS. Progress in Organic Coatings, 64, 497-503. [Google Scholar] [CrossRef] 

为你推荐