锂硫电池硫还原反应金属催化剂的研究进展
Research Progr ess of Metal Catalysts for Sulfur Reduction of Lithium Sulfur Batteries
DOI: 10.12677/JOCR.2023.114030, PDF,    国家自然科学基金支持
作者: 钱思逸, 钱 涛*：南通大学，化学化工学院，江苏 南通
关键词: 锂硫电池；硫还原反应；金属催化剂；Lithium-Sulfur Batteries； Sulfur Reduction； Metal Catalysts
摘要: 一直以来，储能技术着重在能量密度、功率密度、寿命、安全性和成本方面不断改进。近年来不断扩大的电子设备市场，包括电动汽车和便携式电子产品，促使电池逐渐向高能量密度方向发展。尽管锂离子电池已被广泛应用于电动工具、电子通讯设备甚至电动汽车等应用领域，但是锂离子电池的能量密度已接近其理论极限，仅能驱动一辆电动汽车行驶约300公里，或为全功能智能手机供电不到一天。锂硫电池因其较高的理论容量(1675 mAh g−1)和丰富的硫储量而受到了广泛的关注。但是，S8和Li2S的导电性差、循环时巨大的体积膨胀(80%)、多硫化物溶解引起的“穿梭效应”等，会导致活性物质利用率低，电池容量衰减迅速，进而限制了其高功率输出。此外，充放电过程中的非均相氧化还原反应通常伴随着缓慢的反应动力学，这导致了电池的倍率性能不理想。考虑到这些阻碍因素，除了可以通过引入中间层或设计合适的隔膜来捕获和限制锂离子外，寻找合适的正极主体材料也是提高锂硫电池电化学性能的有效途径。具体来说，利用极性材料作为高效的多硫化物介质来加速多硫化锂的反应已经成为近年来的研究热点。一些研究人员发现在硫正极材料中引入电催化剂可以加快硫的氧化还原过程，抑制多硫化锂的穿梭。本综述详细总结了加速硫还原反应的金属催化剂材料的最新进展，包括金属单原子材料、金属纳米材料、金属化合物材料，并为进一步优化锂硫电池的电化学性能指明了方向。
Abstract: Energy storage technology has always focused on improvements in energy density, power density, longevity, safety and cost. The expanding market for electronic devices in recent years, including electric cars and portable electronics, has led to the gradual development of batteries in the direction of higher energy density. Although lithium-ion batteries are already widely used in applications such as power tools, electronic communications devices and even electric cars, their energy density is approaching its theoretical limit, allowing them to drive only about 300 km in an electric car or power a fully functional smartphone for less than a day. Lithium-sulfur batteries due to its high theoretical capacity (1675 mAh g−1) and abundant sulfur reserves and has received the widespread attention. However, the high power output of S8 and Li2S is limited by the low utilization of active materials and the rapid decline of battery capacity due to the poor conductivity of S8 and Li2S, the huge volume expansion (80%) during the cycle, and the shuttle effect caused by the dissolution of polysulfides. Worse still, the heterogeneous redox reaction during charge and discharge is usually accompanied by sluggish reaction kinetics, which leads to the unsatisfactory rate performance of the battery. Considering these hindering factors, in addition to the introduction of an intermediate layer or the design of a proper separator to trap and confine lithium ions, finding a suitable anode main material is also an effective way to improve the electrochemical performance of lithium-sulfur batteries. Specifically, the use of polar materials as efficient polysulfide medium to accelerate the reaction of polysulfide lithium has become a research hotspot in recent years. Some researchers have found that the introduction of electrocatalysts in sulfur cathode materials can accelerate the sulfur redox process and inhibit the shuttle of polylithium sulfide. This review summarizes in detail the latest progress of metal catalysts materials for accelerating sulfur reduction reactions, including metal monatomic materials, metal nanomaterials, metal compound materials, and points out the direction for further optimization of the electrochemical performance of Li-sulfur batteries.
文章引用：钱思逸, 钱涛. 锂硫电池硫还原反应金属催化剂的研究进展[J]. 有机化学研究, 2023, 11(4): 314-333. https://doi.org/10.12677/JOCR.2023.114030

参考文献

[1] Bruce, P., Freunberger, S., Hardwick, L. and Tarascon, J. (2012) Li-O2 and Li-S Batteries with High Energy Storage. Nature Materials, 11, 19-29. [Google Scholar] [CrossRef] [PubMed]
[2] Lin, D., Liu, Y. and Cui, Y. (2017) Reviving the Lithium Metal Anode for High-Energy Batteries. Nature Nanotechnology, 12, 194-206. [Google Scholar] [CrossRef] [PubMed]
[3] Manthiram, A, Yu, X. and Wang, S. (2017) Lithium Battery Chemistries Enabled by Solid-State Electrolytes. Nature Reviews Materials, 2, 1-16. [Google Scholar] [CrossRef] 
[4] Chayambuka, K., Mulder, G., Danilov, D. and Notten, H. (2018) Sodium-Ion Battery Materials and Electrochemical Properties Reviewed. Advanced Energy Materials, 8, Article ID: 1800079. [Google Scholar] [CrossRef] 
[5] Hong, X., Mei, J., Wen, L., Tong, Y., Vasileff, A., Wang, L., Liang, J., Sun, Z. and Dou, S. (2019) Nonlithium Metal-Sulfur Batteries: Steps toward a Leap. Advanced Materials, 31, Article ID: 1802822. [Google Scholar] [CrossRef] [PubMed]
[6] Goodenough, J. and Park, K. (2013) The Li-Ion Rechargeable Battery: A Perspective. Journal of the American Chemical Society, 135, 1167-1176. [Google Scholar] [CrossRef] [PubMed]
[7] Li, M., Lu, J., Chen, Z. and Amine, A. (2018) 30 Years of Lithium-Ion Batteries. Advanced Materials, 30, Article ID: 1800561. [Google Scholar] [CrossRef] [PubMed]
[8] Wang, R., Yang, J., Chen, X., Zhao, Y., Zhao, W., Qian, G., Li, S., Xiao, Y., Chen, H., Ye, Y., Zhou, G. and Pan, F. (2020) Highly Dispersed Cobalt Clusters in Nitrogen-Doped Porous Carbon Enable Multiple Effects for High-Performance Li-S Battery. Advanced Energy Materials, 10, Article ID: 1903550. [Google Scholar] [CrossRef] 
[9] Xu, J., Yu, F., Hua, J., Tang, W., Yang, C., Hu, S., Zhao, S., Zhang, X., Xin, Z. and Niu, D. (2020) Donor Dominated Triazine-Based Microporous Polymer as a Polysulfide Immobilizer and Catalyst for High-Performance Lithium-Sulfur Batteries. Chemical Engineering Journal, 392, Article ID: 123694. [Google Scholar] [CrossRef] 
[10] Ji, H., Wang, Z., Sun, Y., Zhou, Y., Li, S., Zhou, J., Qian, T. and Yan, C. (2023) Weakening Li+ De-Solvation Barrier for Cryogenic Li-S Pouch Cells. Advanced Materials, 35, Article ID: 2208590. [Google Scholar] [CrossRef] [PubMed]
[11] Pope, M. and Aksay, I. (2015) Structural Design of Cathodes for Li-S Batteries. Advanced Energy Materials, 5, Article ID: 1500124. [Google Scholar] [CrossRef] 
[12] Lei, J., Liu, T., Chen, J., Zheng, M., Zhang, Q., Mao, B. and Dong, Q. (2020) Exploring and Understanding the Roles of Li2Sn and the Strategies to beyond Present Li-S Batteries. Chem, 6, 2533-2557. [Google Scholar] [CrossRef] 
[13] Song, Z., Wang, L., Jiang, W., Pei, M., Li, B., Mao, R., Liu, S., Zhang, T., Jian, X. and Hu, F. (2023) “Like Compatible Like” Strategy Designing Strong Cathode-Electrolyte Interface Quasi-Solid-State Lithium-Sulfur Batteries. Advanced Energy Materials, Article ID: 2302688. [Google Scholar] [CrossRef] 
[14] He, J. and Manthiram, A. (2019) A Review on the Status and Challenges of Electrocatalysts in Lithium-Sulfur Batteries. Energy Storage Materials, 20, 55-70. [Google Scholar] [CrossRef] 
[15] Lin, D., Liu, Y. and Cui, Y. (2017) Reviving the Lithium Metal Anode for High-Energy Batteries. Nature Nanotechnology, 12, 194-206. [Google Scholar] [CrossRef] [PubMed]
[16] Gao, N., Zhang, Y., Chen, C., Li, B., Li, W., Lu, H., Yu, L., Zheng, S. and Wang, B. (2020) Low-Temperature Li-S Battery Enabled by CoFe Bimetallic Catalysts. Journal of Materials Chemistry A, 10, 8378-8389. [Google Scholar] [CrossRef] 
[17] Cheng, X., Zhang, R., Zhao, C. and Zhang, Q. (2017) Toward Safe Lithium Metal Anode in Rechargeable Batteries: A Review. Chemical Reviews, 117, 10403-10473. [Google Scholar] [CrossRef] [PubMed]
[18] Liu, B., Zhang, J. and Xu, W. (2018) Advancing Lithium Metal Batteries. Joule, 2, 833-845. [Google Scholar] [CrossRef] 
[19] Kang, X., He, T., Zou, R., Niu, S., Ma, Y., Zhu, F. and Ran, F. (2023) Size Effect for Inhibiting Lithium-Sulfur Batteries. Small, Article ID: 2306503.
https://onlinelibrary.wiley.com/doi/abs/10.1002/smll.202306503
[20] Hou, J., Yang, M., Wang, D. and Zhang, J. (2020) Fundamentals and Challenges of Lithium Ion Batteries at Temperatures between −40 and 60 ˚C. Advanced Energy Materials, 10, Article ID: 1904152. [Google Scholar] [CrossRef] 
[21] Armand, M. and Tarascon, J. (2008) Building Better Batteries. Nature, 451, 652-657. [Google Scholar] [CrossRef] [PubMed]
[22] Palacin, M. (2009) Recent Advances in Rechargeable Battery Materials: A Chemist’s Perspective. Chemical Society Reviews, 38, 2565-2575. [Google Scholar] [CrossRef] [PubMed]
[23] Ji, X., Lee, K. and Nazar, L. (2009) A Highly Ordered Nanostructured Carbon-Sulphur Cathode for Lithium-Sulphur Batteries. Nature Materials, 8, 500-506. [Google Scholar] [CrossRef] [PubMed]
[24] Zhou, L., Danilov, D., Eichel, R. and Notten, P. (2021) Host Materials Anchoring Polysulfides in Li-S Batteries Reviewed. Advanced Energy Materials, 11, Article ID: 2001304. [Google Scholar] [CrossRef] 
[25] Bai, S., Liu, X., Zhu, K., Wu, S. and Zhou, H. (2016) Metal-Organic Framework-Based Separator for Lithium-Sulfur Batteries. Nature Energy, 1, Article No. 16094. [Google Scholar] [CrossRef] 
[26] Ye, H. and Lee, J. (2020) Solid Additives for Improving the Performance of Sulfur Cathodes in Lithium-Sulfur Batteries-Adsorbents, Mediators, and Catalysts. Small Methods, 4, Article ID: 1900864. [Google Scholar] [CrossRef] 
[27] Salem, H., Babu, G., Rao, C. and Arava, L. (2015) Electrocatalytic Polysulfide Traps for Controlling Redox Shuttle Process of Li-S Batteries. Journal of the American Chemical Society, 137, 11542-11545. [Google Scholar] [CrossRef] [PubMed]
[28] Wu, J., Ye, T., Wang, Y., Yang, P., Wang, Q., Kuang, W., Chen, X., Duan, G., Yu, L., Jin, Z., Qin, J. and Lei, Y. (2022) Understanding the Catalytic Kinetics of Polysulfide Redox Reactions on Transition Metal Compounds in Li-S Batteries. ACS Nano, 16, 15734-15759. [Google Scholar] [CrossRef] [PubMed]
[29] Wang, F., Li, J., Zhao, J., Yang, Y., Su, C., Zhong, Y., Yang, Q. and Lu, J. (2020) Single-Atom Electrocatalysts for Lithium Sulfur Batteries: Progress, Opportunities, and Challenges. ACS Materials Letters, 2, 1450-1463. [Google Scholar] [CrossRef] 
[30] Lu, C., Chen, Y., Yang, Y. and Chen, X. (2020) Single-Atom Catalytic Materials for Lean-Electrolyte Ultrastable Lithium-Sulfur Batteries. Nano Letters, 20, 5522-5530. [Google Scholar] [CrossRef] [PubMed]
[31] Zhao, H., Tian, B., Su, C. and Li, Y. (2021) Single-Atom Iron and Doped Sulfur Improve the Catalysis of Polysulfide Conversion for Obtaining High-Performance Lithium-Sulfur Batteries. ACS Applied Materials & Interfaces, 13, 7171-7177. [Google Scholar] [CrossRef] [PubMed]
[32] Ma, C., Zhang, Y., Feng, Y., Wang, N., Zhou, L., Liang, C., Chen, L., Lai, Y., Ji, X., Yan, C. and Wei, W. (2021) Engineering Fe-N Coordination Structures for Fast Redox Conversion in Lithium-Sulfur Batteries. Advanced Materials, 33, Article ID: 2100171. [Google Scholar] [CrossRef] [PubMed]
[33] Zhang, Y., Liu, J., Wang, J., Zhao, Y., Luo, D., Yu, A., Wang, X. and Chen, Z. (2021) Engineering Oversaturated Fe-N5 Multifunctional Catalytic Sites for Drable Lithium-Sulfur Batteries. Angewandte Chemie International Edition, 133, 26826-26833. [Google Scholar] [CrossRef] 
[34] Qiu, Y., Fan, L., Wang, M., Yin, X., Wu, X., Sun, X., Tian, D., Guan, B., Tang, D. and Zhang, N. (2020) Precise Synthesis of Fe-N2 sSites with High Activity and Stability for Long-Life Lithium-Sulfur Batteries. ACS Nano, 14, 16105-16113. [Google Scholar] [CrossRef] [PubMed]
[35] Wang, J., Qiu, W., Li, G., Liu, J., Luo, D., Zhang, Y., Zhao, Y., Zhou, G., Shui, L., Wang, X. and Chen, Z. (2022) Coordinatively Deficient Single-Atom Fe-N-C Electrocatalyst with Optimized Electronic Structure for High-Performance Lithium-Sulfur Batteries. Energy Storage Materials, 46, 269-277. [Google Scholar] [CrossRef] 
[36] Du, Z., Chen, X., Hu, W., Chuang, C., Xie, S., Hu, A., Yan, W., Kong, X., Wu, X., Ji, H. and Wan, L. (2019) Cobalt in Nitrogen-Doped Graphene as Single-Atom Catalyst for High-Sulfur Content Lithium-Sulfur Batteries. Journal of the American Chemical Society, 141, 3977-3985. [Google Scholar] [CrossRef] [PubMed]
[37] Fang, D., Sun, P., Huang, S., Shang, Y., Li, X., Yan, D., Lim, Y., Su, C., Su, B., Juang, J. and Yang, H. (2022) An Exfoliation-Evaporation Strategy to Regulate N Coordination Number of Co Single-Atom Catalysts for High-Performance Lithium-Sulfur Batteries. ACS Materials Letters, 4, 1-10. [Google Scholar] [CrossRef] 
[38] Wang, Z., Shen, J., Xu, X., Yuan, J., Zuo, S., Liu, Z., Zhang, D. and Liu, J. (2022) In-Situ Synthesis of Carbon-Encapsulated Atomic Cobalt as Highly Eefficient Polysulfide Electrocatalysts for Highly Stable Lithium-Sulfur Batteries. Small, 18, Article ID: 2106640. [Google Scholar] [CrossRef] [PubMed]
[39] Huang, T., Sun, Y., Wu, J., Jin, J., Wei, C., Shi, Z., Wang, M., Cai, J., An, X., Wang, P., Su, C., Li, Y. and Sun, J. (2021) A Dual-Functional Fibrous Skeleton Implanted with Single-Atomic Co-Nx Dispersions for Longevous Li-S Full Batteries. ACS Nano, 15, 14105-14115. [Google Scholar] [CrossRef] [PubMed]
[40] Li, Y., Wu, J., Zhang, B., Wang, W., Zhang, G., Seh, Z., Zhang, N., Sun, J., Huang, L., Jiang, J., Zhou, J. and Sun, Y. (2020) Fast Conversion and Controlled Deposition of Lithium (Poly)sulfides in Lithium-Sulfur Batteries Using High-Loading Cobalt Single Atoms. Energy Storage Materials, 30, 250-259. [Google Scholar] [CrossRef] 
[41] Wang, R., Wu, R., Ding, C., Chen, Z., Xu, H., Liu, Y., Zhang, J., Ha, Y., Fei, B. and Pan, H. (2021) Porous Carbon Architecture Assembled by Cross-Linked Carbon Leaves with Implanted Atomic Cobalt for High-Performance Li-S Batteries. Nano-Micro Letters, 13, Article No. 151. [Google Scholar] [CrossRef] [PubMed]
[42] Zhang, S., Ao, X., Huang, J., Wei, B., Zhai, Y., Zhai, D., Deng, W., Su, C., Wang, D. and Li, Y. (2021) Isolated Single-Atom Ni-N5 Catalytic Site in Hollow Porous Carbon Capsules for Efficient Lithium-Sulfur Batteries. Nano Letters, 21, 9691-9698. [Google Scholar] [CrossRef] [PubMed]
[43] Wang, R., Wu, R., Yan, X., Liu, D., Guo, P., Li, W. and Pan, H. (2022) Implanting Single Zn Atoms Coupled with Metallic Co Nanoparticles into Porous Carbon Nanosheets Grafted with Carbon Nanotubes for High-Performance Lithium-Sulfur Batteries. Advanced Functional Materials, 32, Article ID: 2200424. [Google Scholar] [CrossRef] 
[44] Ma, F., Wan, Y., Wang, X., Wang, X., Liang, J., Miao, Z., Wang, T., Ma, C., Lu, G., Han, J., Huang, Y. and Li, Q. (2020) Bifunctional Atomically Dispersed Mo-N2/C Nanosheets Boost Lithium Sulfide Deposition/Decomposition for Stable Lithium-Sulfur Batteries. ACS Nano, 14, 10115-10126. [Google Scholar] [CrossRef] [PubMed]
[45] Zhou, G., Zhao, S., Wang, T., Yang, S., Johannessen, B., Chen, H. Liu, C., Ye, Y., Wu, Y., Peng, Y., Liu, C., Jiang, S., Zhang, Q. and Cui, Y. (2020) Theoretical Calculation Guided Design of Single-Atom Catalysts Toward Fast Kinetic and Long-Life Li-S Batteries. Nano Letters, 2, 1252-1261. [Google Scholar] [CrossRef] [PubMed]
[46] Wang, P., Xi, B., Zhang, Z., Huang, M., Feng, J. and Xiong, S. (2021) Atomic Tungsten on Graphene with UniqueCoordination Enabling Kinetically Boosted Lithium-Sulfur Batteries. Angewandte Chemie International Edition, 133, 15563-15699. [Google Scholar] [CrossRef] [PubMed]
[47] Li, Y., Gao, T., Ni, D., Zhou, Y., Yousaf, M., Guo, Z., Zhou, J., Zhou, P., Wang, Q. and Guo, S. (2022) Two Birds with One Stone, Interfacial Engineering of Multifunctional Janus Separator for Lithium-Sulfur Batteries, Advanced Materials, 34, Article ID: 2107638. [Google Scholar] [CrossRef] [PubMed]
[48] Liu, Z., Zhou, L., Ge, Q., Chen, R., Ni, M., Utetiwabo, W., Zhang, X. and Yang, W. (2018) Atomic Iron Catalysis of Polysulfide Conversion in Lithium-Sulfur Batteries. ACS Applied Materials & Interfaces, 10, 19311-19317. [Google Scholar] [CrossRef] [PubMed]
[49] Wang, C., Song, H., Yu, C., Ullah, Z., Guan, Z., Chu, R., Zhang, Y., Zhao, L., Li, Q. and Liu, L. (2020) Iron Single-Atom Catalyst Anchored on Nitrogen-Rich MOF-Derived Carbon Nanocage to Accelerate Polysulfide Redox Conversion for Lithium Sulfur Batteries. Journal of Materials Chemistry A, 8, 3421-3430. [Google Scholar] [CrossRef] 
[50] Wang, Y., Adekoya, D., Sun, J., Tang, T., Qiu, H., Xu, L., Zhang, S. and Hou, Y. (2019) Manipulation of Edge-Site Fe-N2 Moiety on Holey Fe, N Codoped Graphene to Promote the Cycle Stability and Rate Capacity of Li-S Batteries. Advanced Functional Materials, 29, Article ID: 1807485. [Google Scholar] [CrossRef] 
[51] Zhang, L., Liu, D., Muhammad, Z., Wan, F., Xie, W., Wang, Y., Song, L., Niu, Z. and Chen, J. (2019) Single Nickel Atoms on Nitrogen-Doped Graphene Enabling Enhanced Kinetics of Lithium-Sulfur Batteries. Advanced Materials, 31, Article ID: 1903955. [Google Scholar] [CrossRef] [PubMed]
[52] Shi, H., Ren, X., Lu, J., Dong, C., Liu, J., Yang, Q., Chen, J. and Wu, Z. (2020) Dual-Functional Atomic Znc Decorated Hollow Carbon Nanoreactors for Kinetically Accelerated Polysulfides Conversion and Dendrite Free Lithium Sulfur Batteries. Advanced Energy Materials, 10, Article ID: 2002271. [Google Scholar] [CrossRef] 
[53] Song, C., Li, Z., Ma, L., Li, M., Huang, S., Hong, X., Cai, Y. and Lan, Y. (2021) Single-Atom Zinc and Anionic Fframework as Janus Separator Coatings for Efficient Inhibition of Lithium Dendrites and Shuttle Effect. ACS Nano, 15, 13436-13443. [Google Scholar] [CrossRef] [PubMed]
[54] Han, Z., Zhao, S., Xiao, J., Zhong, X., Sheng, J., Lv, W., Zhang, Q., Zhou, G. and Cheng, H. (2021) Engineering d-p Orbital Hybridization in Single-Atom Metal-Embedded Three-Dimensional Electrodes for Li-S Batteries. Advanced Materials, 33, Article ID: 2105947. [Google Scholar] [CrossRef] [PubMed]
[55] Han, F., Fan, L., Zhang, Z., Zhang, X. and Wu, L. (2023) Platinum Electrocatalyst Promoting Redox Kinetics of Li2S and Regulating Li2S Nucleation for Lithium-Sulfur Batteries. Small, Article ID: 2307950. [Google Scholar] [CrossRef] [PubMed]
[56] Zuo, P., Hua, J., He, M., Zhang, H., Qian, Z., Ma, Y., Du, C., Chen, X., Gao, Y. and Yin, G. (2017) Facilitating the Redox Reaction of Polysulfides by an Electrocatalytic Layer-Modified Separator for Lithium-Sulfur Batteries. Journal of Materials Chemistry A, 5, 10936-10945. [Google Scholar] [CrossRef] 
[57] Yu, M., Zhou, S., Wang, Z., Wang, Y., Zhang, N., Wang, S., Zhao, J. and Qiu, J. (2019) Accelerating Polysulfide Redox Conversion on Bifunctional Electrocatalytic Electrode for Stable Li-S Batteries. Energy Storage Materials, 20, 98-107. [Google Scholar] [CrossRef] 
[58] Zeng, P., Peng, J., Yu, H., Zhou, X., Wang, K., Liu, J., Zhou, Z., Chen, M., Miao, C., Guo, X., Chang, B. and Wang, X. (2022) In-Situ Synthesis of Highly Graphitized and Fe/N Enriched Carbon Tubes as Catalytic Mediums for Promoting Multi-Step Conversion of Lithium Polysulfides. Carbon, 192, 418-428. [Google Scholar] [CrossRef] 
[59] Ye, H., Sun, J., Zhang, S., Lin, H., Zhang, T., Yao, Q. and Lee, J. (2019) Stepwise Electrocatalysis as a Strategy Against Polysulfide Shuttling in Li-S Batteries. ACS Nano, 13, 14208-14216. [Google Scholar] [CrossRef] [PubMed]
[60] Wang, D., Ma, K., Hao, J., Zhang, W., Wang, C., Xu, C., Shi, H., Ji, Z., Yan, X. and Gu, Y. (2021) Multifunction Co-Nx Species to Manipulate Polysulfides Conversion Kinetics toward Highly Efficient Lithium-Sulfur Batteries. Nano Energy, 89, Article ID: 106426. [Google Scholar] [CrossRef] 
[61] Li, Y., Wang, W., Zhang, B., Fu, L., Wan, M., Li, G., Cai, Z., Tu, S., Duan, X., Seh, Z., Jiang, J. and Sun, Y. (2021) Manipulating Redox Kinetics of Sulfur Species Using Mott-Schottky Electrocatalysts for Advanced Lithium-Sulfur Batteries. Nano Letters, 21, 6656-6663. [Google Scholar] [CrossRef] [PubMed]
[62] Su, L., Zhang, J., Chen, Y., Yang, W., Wang, J., Ma, Z., Shao, G. and Wang, G. (2021) Cobalt-Embedded Hierarchically-Porous Hollow Carbon Microspheres as Multifunctional Confined Reactors for High-Loading Li-S Batteries. Nano Energy, 85, Article ID: 105981. [Google Scholar] [CrossRef] 
[63] Yuan, C., Zeng, P., Cheng, C., Yan, T., Liu, G., Wang, W., Hu, J., Li, X., Zhu, J. and Zhang, L. (2021) Boosting the Rate Performance of Li-S Batteries via Highly Dispersed Cobalt Nanoparticles Embedded into Nitrogen-Doped Hierarchical Porous Carbon. CCS Chemistry, 4, 2826-2841. [Google Scholar] [CrossRef] 
[64] Zhao, T., Chen, J., Yuan, M., Dai, K., Zhang, J., Li, S., He, H., Liu, Z. and Zhang, G. (2021) Local Charge Rearrangement to Boost the Chemical Adsorption and Catalytic Conversion of Polysulfides for High-Performance Lithium-Sulfur Batteries. Journal of Materials Chemistry A, 9, 7566-7574. [Google Scholar] [CrossRef] 
[65] Zhang, K., Cai, W., Liu, Y., Hu, G., Hu, W., Kong, Y., Zhang, X., Wang, L. and Li, G. (2022) Nitrogen-Doped Carbon Embedded with Ag Nanoparticles for Bidirectionally-Promoted Polysulfide Redox Electrochemistry. Chemical Engineering Journal, 427, Article ID: 130897. [Google Scholar] [CrossRef] 
[66] Cao, X., Zhang, M., Zhu, F. and Zhang, X. (2022) Fabrication and Characterization of N-Doped Porous Carbon Co-Fe Alloy Composite Cathode Materials for Promoting the Electrochemical Performance of Li-S Batteries. Journal of Alloys and Compounds, 895, Article ID: 162609. [Google Scholar] [CrossRef] 
[67] Hu, Y., Cheng, C., Yan, T., Liu, G., Yuan, C., Yan, Y., Gu, Z., Zeng, P., Zheng, L., Zhang, J. and Zhang, L. (2021) Catalyzing Polysulfide Redox Conversion for Promoting the Electrochemical Performance of Lithium-Sulfur Batteries by CoFe Alloy. Chemical Engineering Journal, 421, Article ID: 129997. [Google Scholar] [CrossRef] 
[68] He, J., Bhargav, A. and Manthiram, A. (2021) High-Energy-Density, Long-Life Lithium-Sulfur Batteries with Practically Necessary Parameters Enabled by Low-Cost Fe-Ni Nanoalloy Catalysts. ACS Nano, 15, 8583-8591. [Google Scholar] [CrossRef] [PubMed]
[69] Zhou, H., Zhang, X., Zou, M., Gu, S., Cai, Y. and Hong, X. (2021) MOF-Derived Bimetal ZnPd Alloy as a Separator Coating with Fast Catalysis of Lithium Polysulfides for Li-S Batteries. ACS Applied Energy Materials, 4, 13183-13190. [Google Scholar] [CrossRef] 
[70] Xu, H., Hu, R., Zhang, Y., Yan, H., Zhu, Q., Shang, J. and Li, B. (2021) Nano High-Entropy Alloy with Strong Affinity Driving Fast Polysulfide Conversion towards Stable Lithium Sulfur Batteries. Energy Storage Materials, 43, 212-220. [Google Scholar] [CrossRef] 
[71] Fang, D., Wang, Y., Qian, C., Liu, X., Wang, X., Chen, S. and Zhang, S. (2019) Synergistic Regulation of Polysulfides Conversion and Deposition by MOF-Derived Hierarchically Ordered Carbonaceous Composite for High-Energy Lithium-Sulfur Batteries. Advanced Functional Materials, 29, Article ID: 1900875. [Google Scholar] [CrossRef] 
[72] Qiao, Z., Zhou, F., Zhang, Q., Pei, F., Zheng, H., Xu, W., Liu, P., Ma, Y., Xie, Q., Wang, L., Fang, X. and Peng, D. (2019) Chemisorption and Electrocatalytic Effect from CoxSny Alloy for High Performance Lithium Sulfur Batteries. Energy Storage Materials, 23, 62-71. [Google Scholar] [CrossRef] 
[73] Chen, Y., Wang, T., Tian, H., Su, D., Zhang, Q. and Wang, G. (2021) Advances in Lithium-Sulfur Batteries: From Academic Research to Commercial Viability. Advanced Materials, 33, Article ID: 2003666. [Google Scholar] [CrossRef] [PubMed]
[74] Wang, P., Xi, B., Huang, M., Chen, W., Feng, J. and Xiong, S. (2021) Emerging Catalysts to Promote Kinetics of Lithium-Sulfur Batteries. Advanced Energy Materials, 11, Article ID: 2002893. [Google Scholar] [CrossRef] 
[75] Li, Z., Wu, J., Chen, P., Zeng, Q., Wen, X., Wen, W., Liu, Y., Chen, A., Guan, J., Liu, X., Liu, W., Zhou, H. and Zhang, L. (2022) A New Metallic Composite Cathode Originated form Hyperbranched Polymer Coated MOF for High-Performance Lithium-Sulfur Batteries. Chemical Engineering Journal, 435, Article ID: 135125. [Google Scholar] [CrossRef] 
[76] Gu, L., Gao, J., Wang, C., Qiu, S., Wang, K., Gao, X., Sun, K., Zuo, P. and Zhu, X. (2020) Thin-Carbon- Layer-Enveloped Cobalt-Iron Oxide Nanocages as a High-Efficiency Sulfur Container for Li-S Batteries. Journal of Materials Chemistry A, 8, 20604-20611. [Google Scholar] [CrossRef] 
[77] Peng, H., Zhang, Y., Chen, Y., Zhang, J., Jiang, H., Chen, X., Zhang, Z., Zeng, Y., Sa, B., Wei, Q., Lin, J. and Guo, H. (2020) Reducing Polarization of Lithium-Sulfur Batteries via ZnS/Reduced Graphene Oxide Accelerated Lithium Polysulfide Conversion. Materials Today Energy, 18, Article ID: 100519. [Google Scholar] [CrossRef] 
[78] Wang, X., Zhao, X., Ma, C., Yang, Z., Chen, G., Wang, L., Yue, H., Zhang, D. and Sun, Z. (2020) Electrospun Carbon Nanofibers with MnS Sulfiphilic Sites as Efficient Polysulfide Barriers for High-Performance Wide-Temperature- Range Li-S Batteries. Journal of Materials Chemistry A, 8, 1212-1220. [Google Scholar] [CrossRef] 
[79] Cai, D., Liu, B., Zhu, D., Chen, D., Lu, M., Cao, J., Wang, Y., Huang, W., Shao, Y., Tu, H. and Han, W. (2020) Ultrafine Co3Se4 Nanoparticles in Nitrogen-Doped 3D Carbon Matrix for High-Stable and Long-Cycle-Life Lithium Sulfur Batteries. Advanced Energy Materials, 10, Article ID: 1904273. [Google Scholar] [CrossRef] 
[80] Yao, Y., Chang, C., Sun, H., Guo, D., Li, R., Pu, X. and Zhai, J. (2022) Hollow Ni3Se4 with High Tap Density as a Carbon-Free Sulfur Immobilizer to Rrealize High Volumetric and Gravimetric Capacity for Lithium-Sulfur Batteries. ACS Applied Materials & Interfaces, 14, 25267-25277. [Google Scholar] [CrossRef] [PubMed]
[81] Shen, Z., Zhang, Z., Li, M., Yuan, Y., Zhao, Y., Zhang, S., Zhong, C., Zhu, J., Lu, J. and Zhang, H. (2020) Rational Design of a Ni3N0.85 Electrocatalyst to Accelerate Polysulfide Conversion in Lithium-Sulfur Batteries. ACS Nano, 14, 6673-6682. [Google Scholar] [CrossRef] [PubMed]
[82] Zhang, H., Dai, R., Zhu, S., Zhou, L., Xu, Q. and Min, Y. (2022) Bimetallic Nitride Modified Separator Constructs Internal Electric Field for High-Performance Lithium-Sulfur Battery. Chemical Engineering Journal, 429, Article ID: 132454. [Google Scholar] [CrossRef] 
[83] Li, Y., Xu, P., Chen, G., Mou, J., Xue, S., Li, K., Zheng, F., Dong, Q., Hu, J., Yang, C. and Liu, M. (2020) Enhancing Li-S Redox Kinetics by Fabrication of a Three Dimensional Co-CoP@Nitrogen-Doped Carbon Electrocatalyst. Chemical Engineering Journal, 380, Article ID: 122595. [Google Scholar] [CrossRef] 
[84] Ye, Z., Jiang, Y., Feng, T., Wang, Z., Li, L., Wu, F. and Chen, R. (2020) Curbing Polysulfide Shuttling by Synergistic Engineering Layer Composed of Supported Sn4P3 Nanodots Electrocatalyst in Lithium-Sulfur Batteries. Nano Energy, 70, Article ID: 104532. [Google Scholar] [CrossRef] 
[85] Weng, W., Xiao, J., Shen, Y. and Liang, X. (2021) Molten Salt Electrochemical Modulation of Iron-Carbon-Nitrogen for Lithium-Sulfur Batteries. Angewandte Chemie International Edition, 60, 24905-24909. [Google Scholar] [CrossRef] [PubMed]
[86] Wang, S., Liu, X., Duan, H., Deng, Y. and Chen, G. (2021) Fe3C/Fe Nanoparticles Embedded in N-Doped Porous Carbon Nanosheets and Graphene: A Thin Functional Interlayer for PP Separator to Boost Performance of Li-S Batteries. Chemical Engineering Journal, 415, Article ID: 129001. [Google Scholar] [CrossRef] 
[87] Wang, B., Wang, L., Zhang, B., Kong, Z., Zeng, S., Zhao, M., Qian, Y. and Xu, L. (2022) Ultrafine Zirconium Boride Nanoparticles Constructed Bidirectional Catalyst for Ultrafast and Long-Lived Lithium-Sulfur Batteries. Energy Storage Materials, 45, 130-141. [Google Scholar] [CrossRef] 
[88] Li, Z., Li, P., Meng, X., Lin, Z. and Wang, R. (2021) The Interfacial Electronic Engineering in Binary Sulfiphilic Cobalt Boride Heterostructure Nanosheets for Upgrading Energy Density and Longevity of Lithium-Sulfur Batteries. Advanced Materials, 33, Article ID: 2102338. [Google Scholar] [CrossRef] [PubMed]
[89] Zhou, Z., Chen, Z., Lv, H., Zhao, Y., Wei, H., Chen, B. and Wang, Y. (2022) A Hollow Co0.12Ni1.88S2/NiO Heterostructure that Synergistically Facilitates Lithium Polysulfide Adsorption and Conversion for Lithium-Sulfur Batteries. Energy Storage Materials, 51, 486-499. [Google Scholar] [CrossRef] 
[90] Xu, Z., Wang, Z., Wang, M., Cui, H., Liu, Y., Wei, H. and Li, J. (2021) Large-Scale Synthesis of Fe9S10/Fe3O4@C Heterostructure as Integrated Trapping-Catalyzing Interlayer for Highly Efficient Lithium-Sulfur Batteries. Chemical Engineering Journal, 422, Article ID: 130049. [Google Scholar] [CrossRef] 
[91] Wang, Y., Xu, L., Zhan, L., Yang, P., Tang, S., Liu, M., Zhao, X., Xiong, Y., Chen, Z. and Lei, Y. (2022) Electron Accumulation Enables Bi Efficient CO2 Reduction for Formate Production to Boost Clean Zn-CO2 Batteries. Nano Energy, 92, Article ID: 106780. [Google Scholar] [CrossRef] 
[92] Cheng, Z., Wang, Y., Zhang, W. and Xu, M. (2021) Correction to Boosting Polysulfide Conversionin Lithium-Sulfur Batteries by Cobalt-Doped Vanadium Nitride Microflowers. ACS Applied Energy Materials, 4, 6375. [Google Scholar] [CrossRef] 
[93] Wang, L., Zhang, M., Zhang, B., Wang, B., Dou, J., Kong, Z., Wang, C., Sun, X., Qian, Y. and Xu, L. (2021) A Porous Polycrystalline NiCo2Px as a Highly Efficient Host for Sulfur Cathodes in Li-S Batteries. Journal of Materials Chemistry A, 9, 23149-23156. [Google Scholar] [CrossRef] 
[94] Wang, Y., Liu, B., Liu, Y., Song, C., Wang, W., Li, W., Feng, Q. and Lei, Y. (2020) Accelerating Charge Transfer to Enhance H2 Evolution of Defect-rich CoFe2O4 by Constructing a Schottky Junction. Chemical Communications, 56, 14019-14022. [Google Scholar] [CrossRef] 
[95] Lu, Y., Qin, J., Shen, T., Yu, Y., Chen, K., Hu, Y., Liang, J., Gong, M., Zhang, J. and Wang, D. (2021) Hypercrosslinked Polymerization Enabled N-Doped Carbon Confined Fe2O3 Facilitating Li Polysulfides Interface Conversion for Li-S Batteries. Advanced Energy Materials, 11, Article ID: 2101780. [Google Scholar] [CrossRef] 
[96] Kim, Y., Noh, Y., Bae, J., Ahn, H., Kim, M. and Kim, W. (2021) N-Doped Carbon-Embedded TiN Nanowires as a Multifunctional Separator for Li-S Batteries with Enhanced Rate Capability and Cycle Stability. Journal of Energy Chemistry, 57, 10-18. [Google Scholar] [CrossRef] 
[97] Shao, A., Zhang, X., Zhang, Q., Li, X., Wu, Y., Zhang, Z., Yu, J. and Yang, Z. (2021) Ultrathin Nanosheet-Assembled Flowerlike NiSe2 Catalyst Boosts Sulfur Redox Reaction Kinetics for Li-S Batteries. ACS Applied Energy Materials, 4, 3431-3438. [Google Scholar] [CrossRef] 
[98] Wang, X., Deng, N., Liu, Y., Wei, L., Wang, H., Li, Y., Cheng, B. and Kang, W. (2022) Porous and Heterostructured Molybdenum-Based Phosphide and Oxide Nanobelts Assisted by the Structural Engineering to Enhance Polysulfide Anchoring and Conversion for Lithium-Sulfur Batteries. Chemical Engineering Journal, 450, Article ID: 138191. [Google Scholar] [CrossRef] 
[99] Chen, K., Zhang, G., Xiao, L., Li, P., Li, W., Xu, Q. and Xu, J. (2021) Polyaniline Encapsulated Amorphous V2O5 Nanowire-Modified Multi-Functional Separators for Lithium-Sulfur Batteries. Small Methods, 5, Article ID: 2001056. [Google Scholar] [CrossRef] [PubMed]
[100] Han, J., Fu, Q., Xi, B., Ni, X., Yan, C., Feng, J. and Xiong, S. (2021) Loading Fe3O4 Nanoparticles on Paper-Derived Carbon Scaffold Toward Advanced Lithium-Sulfur Batteries. Journal of Energy Chemistry, 52, 1-11. [Google Scholar] [CrossRef] 
[101] Tian, Y., Wei, Z., Li, F., Li, S., Shao, L., He, M., Sun, P. and Li, Y. (2022) Enhanced Multiple Anchoring and Catalytic Conversion of Polysulfides by SnO2-Decorated MoS2 Hollow Microspheres for High-Performance Lithium-Sulfur Batteries. Journal of Materials Science & Technology, 100, 216-223. [Google Scholar] [CrossRef] 
[102] Li, N., Ma, H., Wang, L., Zhao, Y., Bakenov, Z. and Wang, X. (2021) Dealloying-Derived Nanoporous Deficient Titanium Oxide as High-Performance Bifunctional Sulfur Host-Catalysis Material in Lithium-Sulfur Battery. Journal of Materials Science & Technology, 84, 124-132. [Google Scholar] [CrossRef] 
[103] Yin, C., Li, Q., Zheng, J., Ni, Y., Wu, H., Kjøniksen, A., Liu, C., Lei, Y. and Zhang, Y. (2022) Progress in Regulating Electronic Structure Strategies on Cu-Based Bimetallic Catalysts for CO2 Reduction Reaction. Advanced Powder Materials, 1, Article ID: 100055. [Google Scholar] [CrossRef] 
[104] Hou, W., Feng, P., Guo, X., Wang, Z., Bai, Z., Bai, Y., Wang, G. and Sun, K. (2022) Catalytic Mechanism of Oxygen Vacancies in Perovskite Oxides for Lithium-Sulfur Batteries. Advanced Materials, 34, Article ID: 2202222. [Google Scholar] [CrossRef] [PubMed]
[105] Gueon, D., Kim, T., Lee, J. and Moon, J. (2022) Exploring the Janus Structure to Improve Kinetics in Sulfur Conversion of Li-S Batteries. Nano Energy, 95, Article ID: 106980. [Google Scholar] [CrossRef] 
[106] He, Z., Wan, T., Luo, Y., Liu, G., Wu, L., Li, F., Zhang, Z., Li, G. and Zhang, Y. (2022) Three-Dimensional Structural Confinement Design of Conductive Metal Oxide for Efficient Sulfur Host in Lithium-Sulfur Batteries. Chemical Engineering Journal, 448, Article ID: 137656. [Google Scholar] [CrossRef] 
[107] Liu, M., Jhulki, S., Sun, Z., Magasinski, A., Hendrix, C. and Yushin, G. (2021) Atom-Economic Synthesis of Magnéli Phase Ti4O7 Microspheres for Improved Sulfur Cathodes in Li-S Batteries. Nano Energy, 79, Article ID: 105428. [Google Scholar] [CrossRef] 
[108] Li, R., Rao, D., Zhou, J., Wu, G., Wang, G., Zhu, Z., Han, X., Sun, R., Li, H., Wang, C., Yan, W., Zheng, X., Cui, P., Wu, Y., Wang, G. and Hong, X. (2021) Amorphization-Induced Surface Eelectronic Sates Modulation of Cobaltous Oxide Nanosheets for Lithium-Sulfur Batteries. Nature Communications, 12, Article No. 3102. [Google Scholar] [CrossRef] [PubMed]
[109] Sun, T., Zhao, X., Li, B., Shu, H., Luo, L., Xia, W., Chen, M., Zeng, P., Yang, X., Gao, P., Pei, Y. and Wang, X. (2021) NiMoO4 Nanosheets Anchored on N-S Doped Carbon Clothes with Hierarchical Structure as a Bidirectional Catalyst toward Accelerating Polysulfides Conversion for Li-S Battery. Advanced Functional Materials, 31, Article ID: 2101285. [Google Scholar] [CrossRef] 
[110] Li, N., Meng, T., Ma, L., Zhang, H., Yao, J., Xu, M., Li, C. and Jiang, J. (2020) Curtailing Carbon Usage with Addition of Functionalized NiFe2O4 Quantum Dots: Toward More Practical S Cathodes for Li-S Cells. Nano-Micro Letters, 12, Article No. 145. [Google Scholar] [CrossRef] [PubMed]
[111] Hu, S., Yi, M., Wu, H., Wang, T., Ma, X., Liu, X. and Zhang, J. (2022) Ionic-Liquid-Assisted Synthesis of N, F, and B Co-Doped CoFe2O4−x on Multiwalled Carbon Nanotubes with Enriched Oxygen Vacancies for Li-S Batteries. Advanced Functional Materials, 32, Article ID: 2111084. [Google Scholar] [CrossRef] 
[112] Cheng, H., Zhang, S., Li, S., Gao, C., Zhao, S., Lu, Y. and Wang, M. (2022) Engineering Fe and V Coordinated Bimetallic Oxide Nanocatalyst Enables Enhanced Polysulfides Mediation for High Energy Density Li-S Battery. Small, 18, Article ID: 2202557. [Google Scholar] [CrossRef] [PubMed]
[113] Li, Z., Zhang, Q., Hencz, L., Liu, J., Kaghazchi, P., Han, J., Wang, L. and Zhang, S. (2021) Multifunctional Cation-Vacancy-Rich ZnCo2O4 Polysulfide-Blocking Layer for Ultrahigh-Loading Li-S Battery. Nano Energy, 89, Article ID: 106331. [Google Scholar] [CrossRef] 
[114] Sun, W., Lu, Y. and Huang, Y. (2021) An Effective Sulfur Conversion Catalyst Based on MnCo2O4.5 Modified Graphitized Carbon Nitride Nanosheets for High-Performance Li-S Batteries. Journal of Materials Chemistry A, 9, 21184-21196. [Google Scholar] [CrossRef] 
[115] Li, Z., Zhou, C., Hua, J., Hong, X., Sun, C., Li, H., Xu, X. and Mai, L. (2020) Engineering Oxygen Vacancies in a Polysulfide-Blocking Layer with Enhanced Catalytic Ability. Advanced Materials, 32, Article ID: 1907444. [Google Scholar] [CrossRef] [PubMed]
[116] Chen, M., Jiang, S., Huang, C., Xia, J., Wang, X., Xiang, K., Zeng, P., Zhang, Y. and Jamil, S. (2018) Synergetic Effects of Multifunctional Composites with More Efficient Polysulfide Immobilization and Ultrahigh Sulfur Content in Lithium-Sulfur Batteries. ACS Applied Materials & Interfaces, 10, 13562-13572. [Google Scholar] [CrossRef] [PubMed]
[117] Tao, X., Wang, J., Ying, Z., Cai, Q., Zheng, G., Gan, Y., Huang, H., Xia, Y., Liang, C., Zhang, W. and Cui, Y. (2014) Strong Sulfur Binding with Conducting Magnéli-Phase TinO2n−1 Nanomaterials for Improving Lithium-Sulfur Batteries. Nano Letters, 14, 5288-5294. [Google Scholar] [CrossRef] [PubMed]
[118] Guo, B., Ma, Q., Zhang, L., Yang, T., Liu, D., Zhang, X., Qi, Y., Bao, S. and Xu, M. (2021) Yolk-Shell Porous Carbon Spheres@CoSe2 Nanosheets as Multilayer Defenses System of Polysulfide for Advanced Li-S Batteries. Chemical Engineering Journal, 413, Article ID: 127521. [Google Scholar] [CrossRef] 
[119] Fan, C., Zheng, Y., Zhang, X., Shi, Y., Liu, S., Wang, H., Wu, X., Sun, H. and Zhang, J. (2018) High-Performance and Low-Temperature Lithium-Sulfur Batteries: Synergism of Thermodynamic and Kinetic Regulation. Advanced Energy Materials, 8, Article ID: 1703638. [Google Scholar] [CrossRef] 
[120] Su, H., Lu, L., Yang, M., Cai, F., Liu, W., Li, M., Hu, X., Ren, M., Zhang, X. and Zhou, Z. (2022) Decorating CoSe2 on N-Doped Carbon Nanotubes as Catalysts and Efficient Polysulfides Traps for Li-S Batteries. Chemical Engineering Journal, 429, Article ID: 132167. [Google Scholar] [CrossRef] 
[121] Sun, W., Li, Y., Liu, S., Liu, C., Tan, X. and Xie, K. (2021) Mechanism Investigation of Iron Selenide as Polysulfide Mediator for Long-Life Lithium-Sulfur Batteries. Chemical Engineering Journal, 416, Article ID: 129166. [Google Scholar] [CrossRef] 
[122] Wang, B., Sun, D., Ren, Y., Zhou, X., Ma, Y., Tang, S. and Meng, X. (2022) MOFs Derived ZnSe/N-Doped Carbon Nanosheets as Multifunctional Interlayers for Ultralong-Life Lithium-Sulfur Batteries. Journal of Materials Science & Technology, 125, 97-104. [Google Scholar] [CrossRef] 
[123] Wu, D., Shi, F., Zhou, G., Zu, C., Liu, C., Liu, K., Liu, Y., Wang, J., Peng, Y. and Cui, Y. (2018) Quantitative Investigation of Polysulfide Adsorption Capability of Candidate Materials in Li-S Batteries. Energy Storage Materials, 13, 241-246. [Google Scholar] [CrossRef] 
[124] Zhong, Y., Yin, L., He, P., Liu, W., Wu, Z. and Wang, H. (2018) Surface Chemistry in Cobalt Phosphide-Stabilized Lithium-Sulfur Batteries. Journal of the American Chemical Society, 140, 1455-1459. [Google Scholar] [CrossRef] [PubMed]
[125] Yu, B., Ma, F., Chen, D., Srinivas, K., Zhang, X., Wang, X., Wang, B., Zhang, W., Wang, Z., He, W. and Chen, Y. (2021) MoP QDs@graphene as Highly Efficient Electrocatalyst for Polysulfide Conversion in Li-S Batteries. Journal of Materials Science & Technology, 90, 37-44. [Google Scholar] [CrossRef] 
[126] Li, W., Chen, K., Xu, Q., Li, X., Zhang, Q., Wen, J. and Xu, J. (2021) Mo2C/C Hierarchical Double-Shelled Hollow Spheres as Sulfur Host for Advanced Li-S Batteries. Angewandte Chemie International Edition, 60, 21512-21520. [Google Scholar] [CrossRef] [PubMed]
[127] Zhang, Y., Zhang, P., Li, B., Zhang, S., Liu, K., Hou, R., Zhang, X., Silva, S. and Shao, G. (2020) Vertically Aligned Graphene Nanosheets on Multiyolk/Shell Structured TiC@C Nanofibers for Stable Li-S Batteries. Energy Storage Materials, 27, 159-168. [Google Scholar] [CrossRef] 
[128] Hong, X., Song, C., Wu, Z., Li, Z., Cai, Y., Wang, C. and Wang, H. (2021) Sulfophilic and Lithophilic Sites in Bimetal Nickel-Zinc Carbide with Fast Conversion of Polysulfides for High-Rate Li-S Battery. Chemical Engineering Journal, 404, Article ID: 126566. [Google Scholar] [CrossRef] 
[129] Balach, J., Linnemann, J., Jaumann, T., Giebeler, L., et al. (2018) Metal-Based Nanostructured Materials for Aadvanced Lithium-Sulfur Batteries. Journal of Materials Chemistry A, 6, 23127-23168. [Google Scholar] [CrossRef] 
[130] Ai, X., Zou, X., Chen, H., Su, Y., Feng, X., Li, Q., Liu, Y., Zhang, Y. and Zou, X. (2020) Transition-Metal-Boron Intermetallics with Strong Interatomic d-sp Orbital Hybridization for High-Performance Electrocatalysis. Angewandte Chemie International Edition, 59, 3961-3965. [Google Scholar] [CrossRef] [PubMed]
[131] He, J., Bhargav, A. and Manthiram, A. (2020) Molybdenum Boride Asan Efficient Catalyst for Polysulfide Redox to Enable High-Energy-Density Lithium-Sulfur-Batteries. Advanced Materials, 32, Article ID: 2004741. [Google Scholar] [CrossRef] [PubMed]

为你推荐