基于ABAQUS的盘式制动器有限元分析
Finite Element Analysis of Brake Disc Based on ABAQUS
DOI: 10.12677/mos.2024.132174, PDF,   
作者: 马靖凯：上海理工大学机械工程学院，上海
关键词: ABAQUS；盘式制动器；有限元分析；ABAQUS； Brake Disc； Finite Element Analysis
摘要: 通过ABAQUS建模模块建立盘式制动器三维模型，基于ABAQUS有限元分析法，研究不同制动转速与不同制动压力下盘式制动器的热力耦合分析。分析结果表明：紧急制动过程中，盘式制动器的温度和应力的最大值与制动转速和制动压力呈正相关。制动转速和制动压力对盘式制动器的温度和应力场产生重要影响。盘式制动器温度和等效应力在圆周上都呈现环带状分布，二者之间存在一致性。这些研究结果为深入了解盘式制动器的温度和应力分布规律以及在不同工作状态下的热力耦合特性提供了参考。
Abstract: The three-dimensional model of the brake disc was established using the modeling module in ABAQUS. The thermal-mechanical coupling analysis of the brake disc under different braking speeds and pressures was conducted using the finite element analysis method in ABAQUS. The analysis results indicate a positive correlation between the maximum temperature and stress of the brake disc and the braking speed and pressure during emergency braking. The braking speed and pressure have a significant influence on the temperature and stress distribution of the brake disc. The temperature and equivalent stress of the brake disc exhibit a consistent ring-shaped distribution along the circumference. These research findings provide valuable insights into the temperature and stress distribution patterns of the brake disc and the thermal-mechanical coupling characteristics under different operating conditions.
文章引用：马靖凯. 基于ABAQUS的盘式制动器有限元分析[J]. 建模与仿真, 2024, 13(2): 1862-1872. https://doi.org/10.12677/mos.2024.132174

参考文献

[1] 方泳龙. 汽车制动理论与设计[M]. 北京: 国防工业出版社, 2007.
[2] 余志生. 汽车理论[M]. 第4版. 北京: 机械工业出版社, 2007.
[3] 孟德建, 张立军, 余卓平. 通风盘式制动器热-机耦合理论建模与分析[J]. 同济大学学报, 2010, 38(6): 890-897.
[4] 鲁国富. 盘式制动器的数值模拟[D]: [硕士学位论文]. 青岛: 青岛理工大学, 2006.
[5] 宋涛. 盘式制动器应力场与温度场多场耦合的数值模拟[D]: [硕士学位论文]. 南昌: 南昌大学, 2014.
[6] 车成力. 汽车制动器的台架试验及摩擦材料的性能分析[D]: [硕士学位论文]. 哈尔滨: 哈尔滨理工大学, 2006.
[7] 廖云霞. 制动器惯性试验台架的研究与开发[D]: [硕士学位论文]. 西安: 长安大学, 2006.
[8] 张帆. 盘式制动器热响应特性仿真与多场模拟试验研究[D]: [硕士学位论文]. 长春: 吉林大学, 2018.
[9] Zagtodzki, P. (1990) Analysis of Thermomechanical Phenomena in Multi-Disc Clutches and Brakes. Wear, 140, 291-308. [Google Scholar] [CrossRef] 
[10] Zagrodzki, P., Lam, K.B., Al Bahkali, E. and Barber, J.R. (2001) Nonlinear Transient Behavior of a Sliding System with Frictionally Excited Thermoelastic Instability. Journal of Tribology, 123, 699-708. [Google Scholar] [CrossRef] 
[11] Hwang, P., Wu, X., Cho, S. and Jeon, Y. (2007) Temperature and Coning Analysis of Ventilated Brake Disc Based on Finite Element Technique. SAE Technical Paper 2007-01-3670. [Google Scholar] [CrossRef] 
[12] Yevtushenko, A. and Kuciej, M. (2010) Temperature and Thermal Stresses in a Pad/Disc during Braking. Applied Thermal Engineering, 30, 354-359. [Google Scholar] [CrossRef] 
[13] Hwang, P. and Wu, X. (2010) Investigation of Temperature and Theramal Stresses in Ventilated Disc Brake Based on 3D Thermo-Mechanical Coupling Model. Mechanical Science and Technology, 24, 81-84. [Google Scholar] [CrossRef] 
[14] Zenon, M. and Istvan, P. (2011) Analysis of Thermal-Elastic Wear Problems. Journal of Thermal Stress, 34, 569-606. [Google Scholar] [CrossRef] 
[15] Belhocine, A. and Bouchetara, M. (2013) Thermal-Mechanical Coupled Analysis of a Brake Disk Rotor. Heat and Mass Transfer, 49, 1167-1179. [Google Scholar] [CrossRef] 
[16] Dufrenoy, P. and Weichert, D. (2014) Experimental Analysis of Hot Spotting in Sliding System. In: Hetnarski, R.B., Ed., Encyclopedia of Thermal Stresses, Springer, Dordrecht, 1485-1494. [Google Scholar] [CrossRef] 
[17] 吴刚, 张东东. 基于ANSYS Workbench的盘式制动器热-机耦合分析[J]. 润滑与密封, 2022, 47(10): 126-133.
[18] 黄健萌. 制动器摩擦热温度场的数值模拟[D]: [硕士学位论文]. 福州: 福州大学, 1999.
[19] 吕振华, 元昌. 蹄-鼓式制动器热弹性耦合有限元分析[J]. 机械强度, 2003, 25(4): 401-104.
[20] 李亮, 宋健, 李永, 郭振宇. 制动器热分析的快速有限元仿真模型研究[J]. 系统仿真学报, 2005, 17(12): 2869-2877.
[21] 韩建荣, 翁建生. 盘式制动器的热分析[J]. 机械设计与制造, 2008(10): 180-182.
[22] 孟祥宝, 基于ANSYS的制动器摩擦生热分析[D]: [硕士学位论文]. 延吉: 延边大学, 2014.
[23] 司杨. 汽车盘式制动器热机耦合研究[D]: [硕士学位论文]. 上海: 同济大学, 2009.
[24] 苏海赋. 盘式制动器热机耦合有限元分析[D]: [硕士学位论文]. 广州: 华南理工大学, 2011.
[25] 曲杰, 苏海赋. 基于代理模型的通风盘式制动器制动盘结构优化设计[J]. 工程力学, 2013, 30(2): 332-3339.

为你推荐